Power Hammer Dies - Recommended Sets

All of our power hammer dies are made of S7 and are interchangeable between any of the power hammer.

#2 Medium Round Eye Punch Carving Chisel

$ 30.00 USD
The medium eye punch is the most commonly used and creates a roughly 1⁄4” eye. Like the small eye punch, the center of the eye is forged, not drilled, allowing for the creation of a pupil. Furthermore, the small eye punch can be used on an eyeball made by the medium eye punch to make a very vivid pupil. The medium eye punch is used for many varieties of animal head, faces such as wizard head, and other carvings.

#1 Small Round Eye Punch Carving Chisel

$ 30.00 USD
The small eye punch is forged to create a roughly 3/16” eye. The centers of this eye punch are forged, not drilled, so that the cone shaped indentation in the center of the eye punch can aid in the effect of creating a pupil. The small eye punch is used for small horse, nail faces, mice and various other carvings.

#17 Tear Drop Punch Carving Chisel

$ 30.00 USD
The teardrop punch is an all around useful tool to create complex curving shapes, a must have for faces. The large side of the teardrop is nearly a 1/2” sphere tapering down to a fine tip on the other end.

#24 The Engraver Carving Chisel

$ 30.00 USD
The engraver in this set is a hybrid of a palm engraver and a tap engraver. Forged in the same rugged manner as the rest of this set, this tool is capable of breathtakingly fine detail in engraving and chasing.

#23 Offset Center Punch Carving Chisel

$ 30.00 USD
The offset center punch mark is perfect for starting an indentation in a piece of steel straight on and then dropping the angle of the chisel and driving along the surface of that piece of steel to create a swell as it plows though.

#22 Center Punch Carving Chisel

$ 30.00 USD
This center punch is by far the best center punch you can buy! With its low profile for high visibility and flared grip, you can use it to make marks on a precision layout and then turn around and drive it deep into hot steel.

#21 Large Fuller Set Hammer Carving Chisel

$ 30.00 USD
The large fuller is based around a roughly 1/4” radius allowing you to make a line in a piece of steel without cutting it. Fullers are used in a wide variety of carving and chasing work from the hollows of a mules ears to the texture around an owl’s eyes.

#20 Small Fuller Set Hammer Carving Chisel

$ 30.00 USD
The small fuller is based around a roughly 3/16” radius allowing you to make a line in a piece of steel without cutting it. Fullers are used in a wide variety of carving and chasing work from the hollows of a mules ears to the texture around an owl’s eyes.

#19 Large Angled Square Set Hammer Carving Chisel

$ 30.00 USD
The large angled square set hammer is roughly 1/2” and used mostly in impression work and chasing for driving down one side of a cut line to create value or the illusion of depth.

#18 Small Angled Square Set Hammer Carving Chisel

$ 30.00 USD
The small angled square set hammer is roughly 3/8” and used mostly in impression work and chasing for driving down one side of a cut line to create value or the illusion of depth.

#16 Whisker Tool Carving Chisel

$ 30.00 USD
This whisker tool is used mainly for texturing. It makes the most wonderful whisker texture that can follow contours and curves.

#15 Large Ball Fuller Carving Chisel

$ 30.00 USD
The large ball fuller is based on a 3/8” sphere that tapers out into a cone. Its uses include larger carving and contouring of surfaces for smooth transition.

#14 Medium Ball Fuller Carving Chisel

$ 30.00 USD
The medium ball fuller is based on a 1/4” sphere that tapers out into a cone. It is perfect for eye sockets, large nostrils and some contouring.

#13 Small Ball Fuller Carving Chisel

$ 30.00 USD
The small ball fuller is based on a 3/16” sphere that tapers out into a cone. It is aggressive enough to start an indentation on a steep curve. As well as making a nice dimple, it can be used to be the start for a larger ball fuller. Normally used for nostrils and stippling.

#12 Large Scoop Carving Chisel

$ 30.00 USD
The large scoop chisel is a butcher ground blade forged around a roughly 1” radius. It can be used in chasing to draw scrolls and circles. For carving, it can be used on one side for a troughing action or flipped over to the other side to cut in and push up a curve, such as the gills or scale on a fish or dragon, or to give the representation of folds in long flowing hair.

#11 Small Scoop Carving Chisel

$ 30.00 USD
The small scoop chisel is a butcher ground blade forged around a roughly 3/4” radius. It can be used in chasing to draw scrolls and circles. For carving, it can be used on one side for a troughing action or flipped over to the other side to cut in and push up a curve, such as the gills or scale on a fish or dragon, or to give the representation of folds in long flowing hair.

#10 Large Bucktooth Butcher Carving Chisel

$ 30.00 USD
The large bucktooth butcher is roughly 1/2” across and is a scaled up version of the small bucktooth butcher. Good for biting in and then pushing material along. Named for its use in carving in and pushing out big square teeth.

#9 Small Bucktooth Butcher Carving Chisel

$ 30.00 USD
The small bucktooth butcher, roughly 3/8” across, is a blunt chisel with a slightly curved blade. Good for biting in and then pushing material along. Named for its use in carving in and pushing out big square teeth.

#8 Straight Carving Chisel

$ 30.00 USD
The straight chisel can cut off a thin slice like the fast cut; its sharp corners give it the ability to put a good hard ending on a line. The straight chisel is used heavily where crisp lines are needed in carving or in the chasing of typed letters and numbers.

#7 Fast Cut Carving Chisel

$ 30.00 USD
Whether you’re cutting off a wire thin tendril or carving in a deep curving line, the fast cut chisel gives you the strength of a crowbar with the cutting edge of a razor blade. Used for cutting in ears, carving out long flowing whiskers, and even splitting down bar stock; the fast cut chisel is a must have from our carving set.

#6- Wolf Eye Punch Carving Chisel

$ 30.00 USD
Wolf eye punches are oval shaped with diamonds as the eye or as the pupil. This provides a very aggressive looking eye that is perfect not only for wolves but also predatory birds, snakes and even very serious horses.

#5 Large Duck Eye Punch Carving Chisel

$ 30.00 USD
As ducks tend to be a little bit on the goofy side anyway, you can never put too big of an eye on a duck. This punch also makes for good pedals and leaves for chase pieces and on impression work.

Bladesmith Tong Set

$ 179.00 USD
A useful addition to any shop, this set includes: 1- Set of 1" Bolt Tongs 1- Set of Hammer Pickup Tongs 1- Set of 2" Pass Through Tongs 1- Set of 1-1/4" Pass Through Tongs

Blacksmith Tong Set

$ 175.00 USD
A useful addition to any shop, this set includes: 1- Set of 1/2" Wolf Jaw Tongs 1- Set of 3/8" V Jaw Tongs 1- Set of Scrolling Tongs 1- Set of 3/8" Bolt Tongs

Essentials Tong Set

$ 210.00 USD
The name says it all, check out what's included in our essential set of tongs: 1- Pair of 1/2" Bolt Tongs 1 Pair of 1" Bolt Tongs 1- Pair of Axe Tongs 1- Pair of Large Plate Tongs 1- Pair of Scrolling Tongs

Bolt Tong Set

$ 179.00 USD
Another great addition to any shop! This set includes: 1 Set of 1/2" Bolt Tongs 1 Set of 3/4" Bolt Tongs 1 Set of 1" Bolt Tongs 1 Set of 3/8" Bolt Tongs

Big BLU Tong Set of 12

$ 499.00 USD
Big BLU Tong Set of 12 This master set includes all 12 tongs rolled into one bundle. This set includes: 1 Pair of 1" Bolt Tongs 1- Pair of 1/2" Bolt Tongs 1 Set of 3/4" Bolt Tongs 1- Pair of 3/8" Bolt Tongs 1- Pair of Hammer Pick Up Tongs 1- Pair of Axe Tongs 1- Pair of Large Plate Tongs 1- Pair of Small Plate Tongs 1- Pair of 1/2" Wolf Jaw Tongs 1- Pair of 3/8" V Jaw Tongs 1- Pair of Scrolling Tongs 1- Pair of Rail Road Spike Tongs

#4 Small Duck Eye Punch Carving Chisel

$ 30.00 USD
The small duck eye is a teardrop punch that will leave a small raised center to represent the duck eye while the teardrop depression acts as the shading around the duck’s eye, killing two birds with one stone. It is normally used on ducks made of 1/2” and 5/8”. It is also useful for some frogs and small snakes.

#3 Large Round Eye Punch Carving Chisel

$ 30.00 USD
The large round eye punch is a very handy tool. While a 3/8” eye is often too large for most hand carved faces unless scaled up, it works very well to create many good elements such as the eye of a flower, the laid back ears of a mouse, and can even be used as a tight scoop.

The Wizards Head Chisels Set

$ 112.00 USD
This set of 4 includes everything you need to carve a wizards head: - #2 Medium Round Eye Punch Carving Chisel (OUT OF STOCK TEMPORARILY CURRENTLY) The medium eye punch is the most commonly used and creates a roughly 1⁄4” eye. Like the small eye punch, the center of the eye is forged, not drilled, allowing for the creation of a pupil. Furthermore, the small eye punch can be used on an eyeball made by the medium eye punch to make a very vivid pupil. The medium eye punch is used for many varieties of an animal head, faces such as wizard head, and other carvings. - #14 Medium Ball Fuller Carving Chisel The medium ball fuller is based on a 1/4” sphere that tapers out into a cone. It is perfect for eye sockets, large nostrils and some contouring. - #17 Tear Drop Punch Carving Chisel The teardrop punch is an all-around useful tool to create complex curving shapes, a must-have for faces. The large side of the teardrop is nearly a 1/2” sphere tapering down to a fine tip on the other end. - #16 Whisker Tool Carving Chisel This whisker tool is used mainly for texturing. It makes the most wonderful whisker texture that can follow contours and curves.

The Horse Head Chisels Set

$ 112.00 USD
This set of 4 includes everything you need to carve a horse head: - #6 Wolf Eye Punch Carving Chisel Wolf eye punches are oval-shaped with diamonds as the eye or as the pupil. This provides a very aggressive looking eye that is perfect not only for wolves but also predatory birds, snakes and even very serious horses. - #8 Straight Carving Chisel The straight chisel can cut off a thin slice like the fast cut; its sharp corners give it the ability to put a good hard ending on a line. The straight chisel is used heavily where crisp lines are needed in carving or in the chasing of typed letters and numbers. - #11 Small Scoop Carving Chisel The small scoop chisel is a butcher ground blade forged around a roughly 3/4” radius. It can be used in chasing to draw scrolls and circles. For carving, it can be used on one side for a troughing action or flipped over to the other side to cut in and push up a curve, such as the gills or scale on a fish or dragon, or to give the representation of folds in long flowing hair. - #23 Offset Center Punch Carving Chisel The offset center punch mark is perfect for starting an indentation in a piece of steel straight on and then dropping the angle of the chisel and driving along the surface of that piece of steel to create a swell as it plows though.

The Daisy Flower Chisels Set

$ 112.00 USD
This set of 4 includes everything you need to carve a daisy flower: - #2 Medium Round Eye Punch Carving Chisel (TEMPORARILY OUT OF STOCK CURRENTLY) The medium eye punch is the most commonly used and creates a roughly 1⁄4” eye. Like the small eye punch, the center of the eye is forged, not drilled, allowing for the creation of a pupil. Furthermore, the small eye punch can be used on an eyeball made by the medium eye punch to make a very vivid pupil. The medium eye punch is used for many varieties of animal head, faces such as wizard head, and other carvings. - #8 Straight Carving Chisel The straight chisel can cut off a thin slice like the fast cut; its sharp corners give it the ability to put a good hard ending on a line. The straight chisel is used heavily where crisp lines are needed in carving or in the chasing of typed letters and numbers. - #12 Large Scoop Carving Chisel The large scoop chisel is a butcher ground blade forged around a roughly 1” radius. It can be used in chasing to draw scrolls and circles. For carving, it can be used on one side for a troughing action or flipped over to the other side to cut in and push up a curve, such as the gills or scale on a fish or dragon, or to give the representation of folds in long flowing hair. ​- #15 Large Ball Fuller Carving Chisel The large ball fuller is based on a 3/8” sphere that tapers out into a cone. Its uses include larger carving and contouring of surfaces for smooth transition.

The Acanthus Leaf Chisels Set

$ 112.00 USD
This set of 4 includes everything you need to carve an acanthus leaf: - #3 Large Round Eye Punch Carving Chisel The large round eye punch is a very handy tool. While a 3/8” eye is often too large for most hand-carved faces unless scaled up, it works very well to create many good elements such as the eye of a flower, the laid back ears of a mouse, and can even be used as a tight scoop. - #7 Fast Cut Carving Chisel Whether you’re cutting off a wire-thin tendril or carving in a deep curving line, the fast-cut chisel gives you the strength of a crowbar with the cutting edge of a razor blade. Used for cutting in ears, carving out long flowing whiskers, and even splitting down bar stock; the fast cut chisel is a must have from our carving set. - #20 Small Fuller Set Hammer Carving Chisel The small fuller is based around a roughly 3/16” radius allowing you to make a line in a piece of steel without cutting it. Fullers are used in a wide variety of carving and chasing work from the hollows of a mules ears to the texture around an owl’s eyes. - #21 Large Fuller Set Hammer Carving Chisel The large fuller is based around a roughly 1/4” radius allowing you to make a line in a piece of steel without cutting it. Fullers are used in a wide variety of carving and chasing work from the hollows of a mules ears to the texture around an owl’s eyes.

NC Whisper Daddy Four-Burner Gas Forge

$ 855.00 USD
Four Burner Forge 6"H x 12"D x 12"W Firebox Rear Bar Stock Door Weight - 71 lbs. Exclusive, high efficiency burners Push Button Ignition Hose, gauge and gegulator included with ALL models. Uniform Heat - Self regulating to 2350°F (1288°C) Fuel of choice - comes fitted for propane (LPG), but may be configured for natural gas (NG) Quick Recovery - heats and reheats metal quickly. No blower required - Venturi Design

NC Whisper Daddy Four-Burner with Open End Ports Gas Forge

$ 985.00 USD
Four Burner Forge 5½"H x 9"D x 16"W Firebox 2" x 3" Bar Stock Ports Weight - 80 lbs. Exclusive, high efficiency burners Push Button Ignition Hose, gauge and gegulator included with ALL models. Uniform Heat - Self regulating to 2350°F (1288°C) Fuel of choice - comes fitted for propane (LPG), but may be configured for natural gas (NG) Quick Recovery - heats and reheats metal quickly. No blower required - Venturi Design

NC Whisper Daddy Model #2 with Open End Ports Gas Forge

$ 812.00 USD
Three Burner Forge 6"H x 9"D x 12"W 2" x 3" Bar Stock Ports Weight - 69 lbs. Exclusive, high efficiency burners Push Button Ignition Hose, gauge and gegulator included with ALL models. Uniform Heat - Self regulating to 2350°F (1288°C) Fuel of choice - comes fitted for propane (LPG), but may be configured for natural gas (NG) Quick Recovery - heats and reheats metal quickly. No blower required - Venturi Design

NC Whisper Daddy Model #2 Gas Forge

$ 750.00 USD
Three Burner Forge 6"H x 9"D x 12"W Firebox 2" x 3" Rear Bar Stock Door Weight - 69 lbs. Exclusive, high efficiency burners Push Button Ignition Hose, gauge and gegulator included with ALL models. Uniform Heat - Self regulating to 2350°F (1288°C) Fuel of choice - comes fitted for propane (LPG), but may be configured for natural gas (NG) Quick Recovery - heats and reheats metal quickly. No blower required - Venturi Design

NC Whisper Lowboy Gas Forge

$ 700.00 USD
Three Burner Forge Low Profile, Open End Ports 3"H x 9"D x 12"W Firebox 2" x 3" Bar Stock Ports Weight - 60 lbs. Exclusive, high efficiency burners Push Button Ignition Hose, gauge and regulator included with ALL models. Uniform Heat - Self regulating to 2350°F (1288°C) Fuel of choice - comes fitted for propane (LPG), but may be configured for natural gas (NG) Quick Recovery - heats and reheats metal quickly. No blower required - Venturi Design

NC Whisper Momma with Open End Ports Gas Forge

$ 645.00 USD
Two Burner Forge 3"H x 6"D x 12"W Firebox 1½" x 3" Bar Stock Ports Weight - 47 lbs. Exclusive, high efficiency burners Push Button Ignition Hose, gauge and gegulator included with ALL models. Uniform Heat - Self regulating to 2350°F (1288°C) Fuel of choice - comes fitted for propane (LPG), but may be configured for natural gas (NG) Quick Recovery - heats and reheats metal quickly. No blower required - Venturi Design anvilfire! Review

NC Whisper Momma Gas Forge

$ 590.00 USD
Two-Burner Forge w/ Insulated Door 3"H x 12"D x 6"W Firebox Rear Stock Door Standard Weight - 45 lbs. Exclusive, high-efficiency burners Push Button Ignition Hose, gauge and regulator included with ALL models. Uniform Heat - Self-regulating to 2350°F (1288°C) The fuel of choice - comes fitted for propane (LPG), but maybe configured for natural gas (NG) Quick Recovery - heats and reheats metal quickly. No blower required - Venturi Design

NC Whisper Baby

$ 465.00 USD
NEW DESIGN AVAILABLE! Hot fit your keg shoes red hot! Works well for smaller jobs. Open-end ports allow bar stock to be run straight through the forge. 3" H x 6½" D x 7" W Firebox 1-1/2″ x 3″ Ports on each end Rear Stock Door Standard Hose, gauge, and regulator included Weight - 37 lbs. Exclusive, high efficiency burners Push Button Ignition Hose, gauge and gegulator included with ALL models. Uniform Heat - Self regulating to 2350°F (1288°C) Fuel of choice - comes fitted for propane (LPG), but may be configured for natural gas (NG) Quick Recovery - heats and reheats metal quickly. No blower required - Venturi Design

NC Knifemaker Forge- 2 Burner Gas Forge

$ 656.00 USD
Firebox 4"H x 4 1/2"W x 13 1/2"L. 2" x 3" exhaust port on one door. Weight 48lbs. • Exclusive, high efficiency burners. • Push-button ignition. • Uniform Heat...Reaches 2350°. • Quick Recovery...heats and reheats metal very quickly. • Flexible...rear bar stock door allows heating sections of bar stock. (Optional on some models.) • No Blower Required. • Fuel of Choice...comes fitted for propane, but may be configured for natural gas. • Hose, gauge, and regulator included.

155_Super_Hammer_4494512

$ 16,990.00 USD

155_Super_Hammer_4494511

$ 16,990.00 USD

155_Super_Hammer_4494510

$ 16,990.00 USD

155_Super_Hammer_4494509

$ 16,990.00 USD

155_Super_Hammer_4494508

$ 16,990.00 USD

155_Super_Hammer_4494507

$ 16,990.00 USD

155_Super_Hammer_4494506

$ 16,990.00 USD

155_Super_Hammer_4494505

$ 16,990.00 USD

155_Super_Hammer_4494504

$ 16,990.00 USD

155_Super_Hammer_4494503

$ 16,990.00 USD

155_Super_Hammer_4494502

$ 16,990.00 USD

155_Super_Hammer_4494501

$ 16,990.00 USD

3/8" Rivet and Ring Tongs

$ 52.00 USD
3/8" Rivet and Ring tongs are low profile and give good control and a light touch. This is good for delicate work like working a hot rivet into plate, but they also excel as a holder for smaller hot working tool like chisels and punches.

Axe Tongs

$ 57.00 USD
Axe Makers tongs allow you to grip the side wall of the eye of an axe with no slipping. The convex and concave jaws also help to reduce or eliminate tool makes during forging. They can hold bar both parallel to the jaws and perpendicular.

2" Pass Through Knife Makers Tongs

$ 57.00 USD
2" Pass Through Knife Makers Tongs, ideal for 3/16" or 1/8" bar stock. These tongs allow material to pass by the boss of the tong. Perfect for bladesmithing.

1-1/4" Pass Through Knife Makers Tongs

$ 57.00 USD
1-1/4" Pass Through Tongs, ideal for 3/16" or 1/8" bar stock. These tongs allow material to pass by the boss of the tong. Perfect for Bladesmithing.

Set of 6 Tong Clips

$ 10.00 USD
This set includes 6 tong clips The mental and physical energy spent to hold your tongs closed should be placed elsewhere while you forge if you can. Tong clips are great and you can never have too many!

Small Scrolling Tongs

$ 42.00 USD

Large Scrolling Tongs

$ 46.00 USD

Rail Road Spike Tongs

$ 48.00 USD

Hammer Pickup Tongs

$ 52.00 USD
Hammer Pickup Tongs are perfect for moving around small items, but they also work very well for large items. This style of tong works well for holding disks, balls and is even perfect for forging hammers.

7/8" Fullering Tools Tongs

$ 42.00 USD
These 7/8" fitted fullering tool tongs can be used for hot work, but come preset to work with any of our fullering tools.

1/2” Wolf Jaw Tongs

$ 47.00 USD
Wolf Jaw tongs are some of the most robust tongs we make, They have an iconic overbuild head that give you some mass around your work, but also can take quite a beating without losing their shape.

Small Plate Tongs

$ 52.00 USD
Small Plate Tongs have a lot of leverage and surface area to hold on to a flat surface as you forge. These small plate tongs are set for 1/8" plate however, they are easily resized.

Large Plate Tongs

$ 52.00 USD
Large Plate Tongs have a lot of leverage and surface area to hold on to a flat surface as you forge. These large plate tongs are set for 1/4" plate however, they are easily resized.

3/8" V Jaw Tongs

$ 48.00 USD

1/4" V Jaw Tongs

$ 52.00 USD
The V jaw tongs are versatile lightweight and low profile tong used for gripping the end of a complex piece of work. They are a staple in any blacksmiths tool kit. While they work best with round and square stock, they will also hold a thinner flat bar rather well.

3/8" Bolt Tongs

$ 52.00 USD

3/4" Bolt Tongs

$ 57.00 USD
3/4" Bolt Tongs are a staple for blacksmiths everywhere. Their V jaw design allows you to grip round and square bar even if that bar is tapered or curved. They can hold bar both parallel to the jaws and perpendicular.

1/2" Bolt Tongs

$ 52.00 USD
1/2" Bolt Tongs are a staple for blacksmiths everywhere, Their V jaw design allows you to grip round and square bar even if that bar is tapered or curved. They can hold bar both parallel to the jaws and perpendicular.

1" Bolt Tongs

$ 62.00 USD
1" Bolt Tongs are a staple for blacksmiths everywhere, now with New Design. Their V jaw design allows you to grip round and square bar even if that bar is tapered or curved. They can hold bar both parallel to the jaws and perpendicular.

Anvil_Order_4494511

$ 2,475.00 USD

BLU Pattern Right Hand Diagonal Hammer

$ 155.00 USD
These diagonal peen hammers are ergonomically designed to work with the natural movements of the body. Made from top-quality forged and heat-treated tool steel. Finished and fitted with a shock-mounted wood handle. These hammers are all hand-dressed and finished by experts. Forged hammers will vary somewhat as they are hand-forged and hand-dressed. Also available in left hand model

BLU Pattern Left Hand Diagonal Hammer

$ 155.00 USD
These diagonal peen hammers are ergonomically designed to work with the natural movements of the body. Made from top quality forged and heat treated tool steel. Finished and fitted with shock mounted wood handle. These hammers are all hand dressed and finished by experts. Forged hammers will vary somewhat as they are hand forged and hand dressed. Also available in right hand model

BLU Pattern Straight Peen Hammer

$ 155.00 USD
These straight peen hammers are ergonomically designed to work with the natural movements of the body. Made from top quality forged and heat treated tool steel. Finished and fitted with a shock mounted wood handle. These hammers are all hand-dressed and finished by experts. Forged hammers will vary somewhat as they are hand-forged and hand-dressed.

BLU Pattern Rounding Peen Hammer

$ 155.00 USD
This popular industry standard hammer is ergonomically designed to work with the natural movements of the body. Made from top quality forged and heat-treated tool steel. Finished and fitted with a shock mounted wood handle. Used by Blacksmiths, Farriers, and Masons. These hammers are all hand-dressed and finished by experts. Forged hammers will vary somewhat as they are hand-forged and hand-dressed.

BLU Pattern Cross Peen Hammer

$ 155.00 USD
This popular industry standard hammer is ergonomically designed to work with the natural movements of the body. Made from top quality forged and heat-treated tool steel. Finished and fitted with a shock mounted wood handle. Used by Blacksmiths, Farriers, and Masons. These hammers are all hand-dressed and finished by experts. Forged hammers will vary somewhat as they are hand-forged and hand-dressed.

K-Pattern Dogface Hammer

$ 150.00 USD

X-Pattern Left Hand Diagonal Hammer

$ 165.00 USD
These diagonal peen hammers are ergonomically designed to work with the natural movements of the body. Made from top-quality forged and heat-treated tool steel. Finished and fitted with a shock-mounted wood handle. Designed to withstand the daily use by the professional blacksmith and farrier. These hammers are all hand dressed and finished by experts. Forged hammers will vary somewhat as they are hand forged and hand dressed.

X-Pattern Right Hand Diagonal Hammer

$ 165.00 USD
These diagonal peen hammers are ergonomically designed to work with the natural movements of the body. Made from top-quality forged and heat-treated tool steel. Finished and fitted with a shock-mounted wood handle. Designed to withstand the daily use by the professional blacksmith and farrier. These hammers are all hand dressed and finished by experts. Forged hammers will vary somewhat as they are hand forged and hand dressed.

X-Pattern Straight Peen Hammer

$ 165.00 USD
Perfectly balanced with one straight crowned face and one flat squared face beveled. Designed to withstand the daily use by the professional blacksmith and farrier. These hammers are all hand dressed and finished by experts. Forged hammers will vary somewhat as they are hand forged and hand dressed.

X-Pattern Rounding Hammer

$ 170.00 USD

Anvil_Only_4494512

$ 2,475.00 USD

Anvil_Only_4494510

$ 2,475.00 USD

Anvil_Only_4494509

$ 2,475.00 USD

Anvil_Only_4494508

$ 2,475.00 USD

Anvil_Only_4494507

$ 2,475.00 USD

Anvil_Only_4494506

$ 2,475.00 USD

Anvil_Only_4494505

$ 2,475.00 USD

Anvil_Only_4494504

$ 2,475.00 USD

Anvil_Only_4494503

$ 2,475.00 USD

Anvil_Only_4494502

$ 2,475.00 USD

Anvil_only_4494501

$ 2,475.00 USD

X-Pattern Cross Peen Hammer

$ 165.00 USD
Perfectly balanced with one cross crowned face and one flat squared face bevelled. Designed to withstand the daily use by the professional blacksmith and farrier. These hammers are all hand dressed and finished by experts. Forged hammers will vary somewhat as they are hand forged and hand dressed.

Pair of 2' Large Top Squaring 50 Ton Press Dies

$ 665.00 USD
This is the set consists of: 2 x 2" Large Top Squaring 50 Ton Press Die You can also purchase this die individually or as a set with a Large Bottom Squaring Press Die

2' Large Top Squaring 50 Ton Press Die

$ 340.00 USD
This is the set consists of: 1 x 2" Large Top Squaring 50 Ton Press Die You can also purchase this die in pair or as a set with a Large Bottom Squaring Press Die

2' Large Top Squaring Die + Large Bottom Squaring Die

$ 620.00 USD
This is the set consists of: 1 x 2' Large Top Squaring Die 1 x Large Bottom Squaring Die You can also purchase each die individually

Pair of Large Bottom Squaring Dies

$ 645.00 USD
This is the set consists of: 2 x Large Bottom Squaring Die Other Options: 1x Large Bottom Squaring Dies
Copyright ©2021 Big Blu Hammer.